At work: When the computer is not used for a short time, the "sleep" mode of the computer is enabled, the energy consumption can be reduced to less than 50%; the computer and display are turned off after lunch break and after work, and the carbon dioxide emissions are reduced by one third.
When the air conditioner starts, the current is large, frequent switching is quite power-consuming, and the compressor is easily damaged. Use the fan wind to improve the cooling effect. After the air conditioner is turned on for a few hours, turn it off and turn on the fan immediately. With this method in the evening, you can not turn on the air conditioner all night, saving nearly 50%.
Planting some air-purifying plants in the office, such as: orchids, gerberas and other absorbable formaldehyde, can also decompose benzene emitted from copiers, printers, and can swallow nicotine.
In life: the amount of food stored in the refrigerator is 80% of the volume, and the electricity is too much or too little. A gap of about 10 mm or more should be left between foods and between food and refrigerator. Use a few plastic boxes to hold the water, put it into the freezer after making ice in the freezer, which can increase downtime and reduce boot time.
Washing machine: In the same long washing time, the use of strong gear actually saves electricity compared to the weak gear, and can extend the life of the washing machine. Generally dehydration does not exceed 3 minutes.
Microwave oven: The food for heating or cooking should not exceed 0.5 kg. It is best to cut into small pieces. When the amount is too much, it should be heated in different time periods. Stir in the middle and use "high fire" as much as possible.
Gas: Shorter cooking time with a small fire can reduce heat loss. However, it is not advisable to let the fire go beyond the bottom of the pot to avoid wasting gas. Do not cover before boiling water in summer, and then cover it when it is naturally warmed to air temperature to save gas. China Energy Saving Lamp
About high speed Door Accessories:
1.Driving system: High Speed Door Servo System motor and control, motor SNMA / SEJ +reducer+flang+encoder+control box
2.Other accessories: Middle aluminium bar, bottom aluminium bar, aluminium vertical track, stainless steel vertical track, brushes,round nylon strip, PVC roll, rolling steel tube complete, drum be;;s for rolling tube, side end covers, stainless steel cover, steel tubes, air bag sensor system, safety light beam, Microwave sensor 24 Gigahertz,PVC welding machine, smoke and fire sensors, PVC transparent window, magnetic loop, photocell, remote control, manual push button, sound warning alarm Led lamp traffic light
For some main accessories, here is detain introduction:
1).24G radar sensor:
Brand: Hofic
Technology: Microwave processor
Maintain time: 0.5s
Protection: IP54
Transmitting frequency: 24.125GHz
Maximum installation height: <5meter
Transmitting power density: <5mw/cm2
Power consumption: <1W(VA)
Installation angle: 0-90°(lengthways) -30-30°(crosswise)
Supply voltage: AC&DC 12V-30V
2).Photocell:
Approval CE & ISO9001
Power supply AC/DC 12-30V
Static current 25A
Action current 40mA
Mounting distance Max 10m
NO or NC contact Done by NO./NC. contact selection
Working environment temperature -42℃ to +45℃
Working environment humidity 10 to 90%RH
Appearance dimensions( controller) 123*50*32mm(L*W*H)
Appearance dimensions(Magic eye head) 19*13mm(L*D)
3). Remote control
Operating Voltage: AC220V/50HZ+-20%
Transmit power:≤100mW;Super regenerative module, strong anti-interference
Operating temperature:-30℃-+70℃
Working frequency: 433MHZ;transmitter 1527, millions of encoding chip
Accept sensitivity:≤110dB
Manipulation method: electric remote control
Configure the quantity: Wireless number; factory configuration transmitter two. Can be equipped with PT2272 digital decoder chip
Configure the function: Up, down, stop, anti-lock full-featured reproduction
4). Magnetic loop
Voltage: 12V AC/DC +-10% 24V 115V AC+-10% 230V
Power: <2VA
Continued electrical output: 7A / 250V AC
Frequency range: 20 to 200K Hz
Response time: infinity (factory setting) or adjust maintain time
Sensitivity: 0.01% to 0.1% divided into 3 levels
Protection level: IP30
Electromagnetic compatibility (EMC) Complies with EM50081-1 and EN50082-2
Detection loop inductance: the limit of 40uH to 100uH ideal value 80uH to 300uH
Operating temperature: -25 ℃ to 70 ℃
Storage temperature: -40 ℃ to 85 ℃
Relative humidity: <90% non-condensing
Temperature compensation: automatic compensation up to 50 ℃ / h
Connection type: 11 pin DIN rail socket
Dimensions: 41 * 78 * 85 mm (width * height * length)
Weight: 250 grams
5). manual push button
This exit switch button is made of ABS and has built-in indicator light make it looks more elegant and fashionbale. It can be widely used in public entrance gates, public door, home, office, hotel, etc.
Door Exit Button Push To Exit Switch Door Opener For Access Control Security
Main Feature
Fashionable appearance
Made of ABS Plastic
Easy to install and operate
Used for access control
Specification
Mechanical Life: 500,000 test
Material: Plastic
6). Limit switch encoder
Voltage: DC5V-24V
Output voltage: high voltage≥85%Vcc, low voltage≤0.5V
Maximum mechanical speed:6000rpm
Anti-vibration: 50m/s,10-200HZ,XYZeach way 2 times.
Current consumption:≤30mA
Response frequency: 0-100KHZ
Protection: waterproof,oil proof,dust prevention, IP54
The output code system: binary code
Operating life: MTBF≥30000(+25℃,2000rpm)
Rotational inertia:4.0x10-8kgm²
Maximum load:radial direction20N
Axial direction:10N
Weight: about 0.4kg
High Speed Door Accessories,High Speed Door,Electronic High Speed Door Accessories
Shenzhen Hongfa Automatic Door Co., Ltd. , https://www.hffastdoor.com