Analysis of the precautions of the bearing device

Source: China Bearing Network Time: 2013-03-08

/*250*250 was created on 2017/12/25*/ var cpro_id = 'u3171089';

First, the bearing device: The bearing device must be carried out under boring and hygienic environmental conditions. Before the device, carefully check the cooperation appearance of the shaft and the outer casing, the end face of the shoulder, the groove and the processing quality of the joint appearance. All cooperation It is necessary to carefully remove and remove the burrs on the outside; it is necessary to remove the sand from the unprocessed appearance of the casting.
Before the bearing device, it should be cleaned with gasoline or kerosene; it should be used after boring; and it should be excellent and smooth; the bearing should be smooth and smooth; the oil should be smooth. When the grease is smooth, it should be free from impurities, oxidation and rust. Smooth grease with excellent function such as extreme pressure. Smooth grease filling capacity is 30%-60% of bearing and bearing housing volume; not too much. Double row tapered roller bearing and water pump shaft bearing with sealing layout have been filled with smooth grease Users can use it directly; no more can be cleared.
When bearing the device; it is necessary to apply equal pressure on the circumference of the end face of the ferrule; press the ferrule; do not directly hit the bearing end face with the number one thing; avoid damage to the bearing. Under the condition of small interference; Press the sleeve on the end face of the bearing ring at normal temperature; hit the sleeve with the head; press the sleeve evenly through the sleeve. If it is a large-scale device; use a hydraulic press. When pressing in; ensure the outer ring end face and The shoulder end face of the outer casing; the inner ring end face and the end face of the shaft shoulder are pressed tightly; no gap is allowed.
When the interference is large; you can use oil bath heating or induction heating to install the device; the heating temperature is 80 Â°C-100 Â°C; the maximum can not exceed 120 Â°C. Together; use nuts or other appropriate means to tighten the bearing In order to avoid the shortening of the width direction of the bearing after cooling, the gap between the ferrule and the shoulder can be adjusted. The clearance of the single row tapered roller bearing device should be adjusted. The clearance value should be based on different operating conditions and cooperation. The quantity is fine and detailed. If necessary, it should be determined experimentally. The double row tapered roller bearing and the pump shaft bearing have been adjusted at the factory; the device does not need to be adjusted.
After the bearing device, the rotation test should be carried out; firstly, it should be used for rotating shaft or bearing box; if it is not abnormal; it will be driven without load and low speed by power; then gradually increase the rotation speed and load according to the working condition; and detect noise, oscillation and temperature rise. Found abnormal; should stop the operation and check. After the operation experiment is normal, it can be delivered.
Second, the disassembly of the bearing: After the bearing is removed, it is intended to be used continuously; the appropriate disassembly should be used. The ferrule of the interference cooperation should be dismantled; only the pulling force should be added to the ferrule; Pass the disassembly force; otherwise the roll and raceway will be crushed.
Third, the operating environment of the bearing: According to the application site and operating conditions and environmental conditions to select the standard scale, accuracy; cooperative bearing is the condition to ensure the bearing life and reliability.
1. Application parts: Tapered roller bearings are suitable for accepting radial and axial combined loads with radial loads; usually used with two sets of bearings; the first should be the front and rear wheels of the car, the automatic bevel gear, the differential Transmission parts such as reducer and reducer.
2, promise speed: in the correct, smooth and outstanding environment; the maximum speed of the bearing is 0. 3-0. 5 times. Under normal conditions; the limit speed of 0.2 times is the most suitable.
3, promised slanting angle: Tapered roller bearings usually do not allow the shaft to be skewed relative to the housing hole; if there is skew; the maximum does not exceed 2'.
4, promise temperature: in the normal load; and the smoothing agent has high temperature resistance; and smooth and plentiful conditions; usually the bearing promises to work at -30 Â° C -150 Â° C ambient temperature.

Recommend to friends comments close window

Bearing related knowledge

Bearing limit speed miniature bearing overview and instructions for use
PVD skills in the bearing occupation of the use of rolling bearing device elements, the details of the special process of rolling bearing process

This article links to http://
Please indicate the bearing network http://

Previous: Analysis of the application method of SKF bearing Next: Machine tool spindle and bearing

Fitting For Two-piece Toilet

Fittings for two piece toilet:

1. inlet valve ( lower pressure inlet valve and high pressure inlet valve)

2. flush valve and accessories for two piece toilet

Direct factory with professional R&D department, product range covers Smart Toilet, Bidet cover, toilet seat, tank fittings, flush tank, flush valves, and Intelligent Toilet.

Fitting For Two-Piece Toilet,Dual Flush Valve,Flush Tank Fitting,Sanitary Ware Fitting

XIAMEN JIEENTE IMPORT AND EXPORT CO.,LTD , https://www.jieente.cn