![<?echo $_SERVER['SERVER_NAME'];?>](/template/twentyseventeen/skin/images/header.jpg)
The decoration of the bathroom must not be neglected. The installation of the corresponding sanitary ware especially requires us to be cautious. The installation of sanitary ware not only affects the aesthetics of our decoration, but also affects the comfort we use. The following small series will give a detailed introduction to the installation of sanitary ware.
Sanitary ware installation: bathtub installation
First, carry out the test to see if there is any leakage: before we put the bathtub, we need to install the corresponding water fittings, and we need to do a good job of closing the water for 24 hours, then look at the leakage of the bathtub, especially Pay attention to the overflow.
Second, the bathtub leveling: When we are laying the bathtub, we must pay attention to the corresponding water outlet is lower than the inlet end, so as to avoid the poor discharge. The corresponding bathtub should not only be visually level, but also pay attention to not affect the drainage.
Third, sand filling: Relative to the cast iron bathtub, it is strong but the thermal conductivity is very fast, so it is necessary to use the Zhonghe sand for bottoming. Of course, foam can also be used because the foam does not have fluidity. It is also necessary to pay attention to the fact that the sand cannot leak into the downpipe when filling the river sand.
Fourth, the inspection and repair: we also need to pay attention to the location of the water in the water outlet 300mm wide and 400mm holes, according to the size of the waterproof and anti-corrosion treatment. The purpose of this is to have a good mouth in the future when we are doing maintenance.
Installation of sanitary ware: installation of washbasin
First, the installation of the washbasin: When we install the pipe rack washbasin, we must first draw the line of the lower water pipe, then measure the height of the ground upwards, and draw a horizontal line on the wall. Mark the mark according to the width of the washbasin, and then make a 120 mm deep hole. Clean up the relevant debris and keep the installation parts clean.
Second, the installation of the cast iron frame washbasin: the same as the above installation, also need to mark the center of the lower water pipe, and then measure the height, and draw horizontal lines to form a cross. According to the width of the washbasin and then mark on the center line, and the pot holder is placed, the position of the screw hole is reserved, and the size needs to be marked.
Sanitary ware installation: toilet installation
First, take out the pipe plug of the ground drain, then check if there are any debris in the pipe, and if necessary, remove the corresponding debris. Then clean the circumference of the nozzle, and then connect the corresponding outlet of the toilet to the lower water outlet to make it level and correct. Then we need to mark the bolt holes in the toilet.
Second, punch holes. Corresponding holes of 20 mm in diameter and 60 mm in depth are required at the corresponding stamps. Then insert the bolt into the hole, then use cement to secure it and align the toilet eye with the bolt. Then, the putty is applied around the corresponding water outlet of the toilet and the lower water pipe mouth, and the corresponding four bolt holes of the toilet are screwed until the tightness is moderate.
Third, install the rear end of the toilet bowl. It should be installed according to the corresponding drawings or the lined part, and the relevant bolts need to be fixed. The degree of fixing needs to be moderate and not too tight.
Fourth, install the back water tank. When installing the water tank, we need to pay attention to the moderate size, not too loose or too tight.
Fifth, pick up the water. The installation of the water supply system also needs attention, and it is impossible to leak water. Pay attention to the tightness of the tightness when you receive the water.
When installing sanitary ware, we also need to pay attention to check the relevant water leakage. The above is the installation procedure for the sanitary ware that Xiaobian explained for everyone today. I believe everyone knows it. I hope this article can help you.
LED wall sconces are a fantastic way to add style, sophistication, and security to any home or outdoor space. These modern wall lights offer an energy-efficient and long-lasting alternative to traditional lighting options such as outdoor wall sconces or battery wall lights. With an LED wall lamp, you can create a warm and inviting atmosphere while also providing ample illumination to your outdoor space. Whether you are looking to enhance your home's curb appeal or want to create a cozy and inviting outdoor entertainment area, LED wall sconces are the perfect solution. So, if you are looking to upgrade your lighting and add a touch of modern elegance to your home or outdoor space, look no further than LED wall sconces.
Outdoor Wall Sconces ,Battery Wall Lights ,Modern Wall Lights ,Led Wall Lamp
Ningbo Le Monde Lighting Co.,Ltd , https://www.nblemonde-lighting.com