There are consumers who need to install tempered glass doors in the bathroom, but do not know how to install them. Xiaobian specially organizes some materials for reference.
Tempered glass is a glass with high wind pressure resistance, cold and heat resistance, and even if it is broken, the fragments are uniform small particles, instead of the knife-shaped sharp corners left after the ordinary glass is broken, so the system is made. The tempered glass door is also considered a safety glass door. Even so, tempered glass door glass still has a self-explosion rate of three thousandths. In addition to the quality of tempered glass, whether the installation is rigorous is also an important factor related to safety.
How to install and install the bathroom tempered glass door
1, line positioning
The scribing is mainly for positioning the pin hole plate of the revolving pin and the rotating shaft connecting plate of the floor spring. The tempered glass door has upper and lower metal rails, and the scribe line is completed in two metal rails.
2, cutting tempered glass
If the tempered glass door does not meet the installation size, it is very troublesome to rework, so it is necessary to be accurate when starting the measurement. The measurement of tempered glass mainly includes two aspects of the width and height of the glass plate. When measuring the width of the glass plate, measurements were made at the bottom, middle, and top, respectively, and the minimum size was selected as the width of the cut. If the data obtained from the top, middle and bottom are identical, then 3-5 mm is reduced in the measured dimensions as the cutting width of the glass. Similarly, the height of the glass plate should include the installation location for inserting the upper and lower rails, so it is generally taken to cut less than 3-5 mm of the measured data.
After the glass plate is cut by size, it is usually necessary to chamfer the four corners. If the worker is chamfering on the spot, in order to prevent the collapse of the collapse, it is best to use a fine grinding wheel to slowly grind the operation.
3, fixed bottom support
The glass door bottom is made of two materials, one is a wooden bottom and the other is an aluminum square tube. The first stainless steel veneer can be fixed with wooden wedges and nails; if it is an aluminum alloy square tube, it can be fixed on the frame with aluminum angles, or the wooden wedge can be buried and fixed with wood screws. On the wooden wedge.
4, install tempered glass door leaf
Use a glass suction cup to first pass the glass plate to the west and place the glass in place. Insert the upper part of the glass into the limit groove of the door frame, and then place the lower part of the glass plate in the opposite seam of the bottom cover. A wooden strip is nailed on the bottom of the wooden base, and a universal glue is applied to the wooden strip about 4 mm from the surface of the glass plate, and the glass plate is fixed on the bottom support.
5, injection seal
The glass plate is fixed in thickness, and is sealed at the fixing portion of the top limit groove and the bottom plate, and at the seam of the glass plate and the frame column. Use a plastic sheet to flatten the glue on both sides of the glass and wipe off the residue. Be careful when wiping the remnants. Try not to use sharp objects such as blades.
6, fixed door leaf up and down rail
After the height of the door is determined, the glass strips are inserted into the gaps on both sides of the crosspiece, and small wooden strips are inserted from both sides, tapping and stabilizing, and injecting glass glue into the gap formed between the small wooden strips, the door leaf glass and the crosspiece, The residue is treated as above.
7, fixed activity door leaf
There is a positioning pin on the beam of the tempered glass door frame, and the adjusting screw of the positioning pin needs to be adjusted out of the plane of the beam by 1-2 mm. The glass door leaf is erected, and the hole position of the rotating pin connecting member in the lower rail of the door leaf is aligned with the rotating pin shaft of the floor spring, and the door leaf is rotated to fit the hole position on the rotating pin shaft. The door leaf is rotated by 90°, and forms a right angle with the door frame beam. The hole of the rotating connecting piece in the crosspiece of the door leaf is aligned with the positioning pin on the door frame beam, and the positioning pin is inserted into the hole by about 15 mm.
Xiaobian Conclusion: The above is the specific method and details of the installation of tempered glass doors, which helps everyone to communicate with the installation workers in time for decoration. It’s a matter of safety, don’t take it lightly!
Note: The above content is from the network and is for reference only.
Suzhou Newstar Hardware Co.,Ltd is China manufacturer of Tool Cabinet Trolley Tool Set in Suzhou, nearby Shanghai port. We provide different modules of tool box cabinet set, tool cabinet trolley tool set case, tool chest with tools. And also other kinds of tool kits in blow case, aluminum box, bags, etc. We have experienced ability in OEM and ODM services, could provides customer with customized needs. Please contact us.
Tool Cabinet Trolley Tool Set,Tool Box Cabinet Set,Tool Cabinet Trolley Tool Set Case,Tool Chest With Tools
SUZHOU NEWSTAR HARDWARE CO.,LTD. , https://www.hardwarenewstar.com