Hot Rolled 440c Stainless Steel Plate for Making Knife

1:Brief Introduction Of 440C stainless steel:
Grade 440C stainless steel is a high carbon martensitic stainless steel. It has high strength, moderate corrosion resistance, and good hardness and wear resistance. Grade 440C is capable of attaining, after heat treatment, the highest strength, hardness and wear resistance of all the stainless alloys. Its very high carbon content is responsible for these characteristics, which make 440C particularly suited to such applications as ball bearings and valve parts.
Corrosion Resistance:
*Good resistance to the atmosphere, fresh water, foods, alkalies and mild acids. Best resistance in the hardened and tempered and passivated condition. A smooth polished surface also assists.
*The corrosion resistance of grade 440C approximates that of grade 304 in many environments.
Heat Resistance:
*Not recommended for use in temperatures above the relevant tempering temperature, because of reduction in mechanical properties by over-tempering.
Heat Treatment:
*Annealing - Full anneal - 850-900°C, slow furnace cool to about 600°C and then air cool. Sub-critical Annealing - 735-785°C and slow furnace cool.
H*ardening - Heat to 1010-1065°C, followed by quenching in warm oil or air. Oil quenching is necessary for heavy sections. Immediately temper at 150-370°C to obtain a wide variety of hardness values and mechanical properties as indicated in the accompanying table.
*Tempering in the range 425-565°C is to be avoided because of reduced impact resistance and corrosion resistance. Tempering in the range 590-675°C results in lower hardness (the product become machinable) and high impact resistance.
Welding:
*If welding is necessary pre-heat at 250°C and follow welding with a full anneal. Grade 420 filler will give a high hardness weld (although not as high as the 440C), but 309 or 310 will produce soft welds with higher ductility.
Machining:
*In the annealed condition this grade is relatively easily machined; approximately the same as for high speed steel. Chips are tough and stringy so chip breakers are important. If these grades are hardened machining becomes more difficult and probably impossible.

Other Grades:
201,202,21-4N,301,302,301L,303,303Se,304,304L,304H,304LN,304N,305,S38400,308,309,309S,310,310s,
316,316L,316H,316Ti,316N,316LN,317,317L,317LMN,317LN,321,321H,347,347H,S3100,S31803,S3205,
S32304,S31200,S31260,S32507,405,409,429,430,430F,434,444,403,410S,410,416,420,420F,431F,440A
440B,440C,440F,610,630,631,632,635,660,Alloy 200,Monel 400 ,Alloy K-500 ,Inconel 600 , Incconel 601,
Inconel 625 , Inconel 718 , Alloy 800 ,Alloy 800H,Alloy 800HT,Inconel 825,Alloy 276, Alloy 20, Alloy 59

2:Chemical Composition with different standards:
3:Stainless Steel Plate Process:


4:Stainless Steel Plate Package:


5:About us:
Tianjin Zhongyantiancheng Steel Co.,Ltd(short for ZYTC ) is a professional manufacturer and exporter of steel products in China, located in Tianjin Beichen District, having the biggest port in North China.
With 20 years of development, the group has become the leader in steel, product variety, complete specifications and so on in North China market, large inventories more than 100,000 tons are maintained all the time.
ZYTC is specialized in steel products, especially Stainless steel pipe,Stainless steel bar,Stainless steel plate (TG,KSK,BG,Krupp), Round bar(SHOUGANG,DAYE), Spiral pipe(LIDA), Aluminum steel plate,Aluminum pipe ,Copper and so on . 
ZYTC has cooperated with Tianjin Seamless Steel Tube Plant(TPCO), Baotou Steel Pipe Plant, Chengdu Steel Pipe Plant, Anshan Steel Pipe Plant,Baoshan Steel Pipe Plant and other steel pipe plants.Round bar cooperated with Beijing shougang goup,Tonggang steel group, Daye steel bar group ,Benxi bengang group an so on , Baotai titanium group,Baoji Lixing group,Stainless steel plate cooperated with Shanxi TAIGANG Steel Plate grouop,Baogang group,Shanghai Kelubo group ,and Puxiang steel group. all these corporations mentioned above are our shareholder partners. 
ZYTC principle is: supplying the best products and service,being the best supplier.
The company can make steel product according to particular specifications and materials. ZYTC will perfect our quality management system and supply products of high quality to our customers.
We are all looking forward to establishing business relationships with customers all over the world!

6:Why choose us?
* More than 20 years experience in stainless and aluminum steel fields.
* Samples available.
* Specialist metallurgic advice and flexible service.
* High level of expertise, in-depth product knowledge.
* Competitive price, high quality,rich experiences and high reputation
* Delivered on time.
* Good after-sale service.
* Well recognized and trusted by customers.

7: Other productions:

High Frequency Ranging Sensor Module

A high frequency ranging sensor module is a device that uses high-frequency signals to measure the distance between the sensor and an object. It typically consists of a transmitter and a receiver, which emit and receive high-frequency signals, respectively.
The module works by sending out a high-frequency signal, such as ultrasonic or radar waves, and measuring the time it takes for the signal to bounce back after hitting an object. By calculating the time of flight, the module can determine the distance between the sensor and the object.
High-frequency ranging sensor modules are commonly used in various applications, such as robotics, industrial automation, and automotive systems. They provide accurate distance measurements and can be used for obstacle detection, object tracking, or proximity sensing.

Laser Distance Sensor Arduino,Laser Distance Sensor Analog Output,Precision Laser Distance Sensor,Optical Distance Sensors,USB Laser Distance Sensor

CHENGDU MESKERNEL INTEGRATED TECHNOLOGY CO.,LTD , https://www.meskernel.com