![<?echo $_SERVER['SERVER_NAME'];?>](/template/twentyseventeen/skin/images/header.jpg)
During the renovation process, there will always be some tangling in the construction sequence, such as wall tiles and floor tiles, which are often tangled in the end. A typical mason master uses two processes at the tiling stage. The most common is the brick floor tile, that is, the order of the tiles is the first floor tile. There is also a more demanding requirement for geotechnical work, which is the process of pressing bricks and floor tiles. Workers are required to put tiles on the tiles and then tile them. So which of these two different tiling techniques are even more so?
Ms. Wu of Jinfeng Apartment: Recently, the house is being renovated and the tiling stage has been reached. The master said that it is better that the tiles are better to be pressed against the floor tiles, but before I heard that the wall tiles were pressed against the floor tiles, the tiles were pressed. Wall tiles, in fact, are not very understanding, what is the difference between the two in the end, and what should be done?
Supervisor Q: During the renovation process, the general mason master will use two kinds of crafts at the stage of tiling. The most common is the brick floor tile, that is, the order of the tiles is the first floor tile. There is also a more demanding requirement for geotechnical work, which is the process of pressing bricks and floor tiles. Workers are required to put tiles on the tiles and then tile them. So which of these two different tiling techniques are even more so?
| First, what is wall tile, floor tile wall tile! |
From the figure, we can easily see why bricklayers are generally reluctant to do the wall tile pressing process. This is not only an effortless task, but some bricklayers are not at the level and have not done such a process. Did not dare to take over at all.
Why is it difficult to press bricks and tiles? If it is a brick pressing wall tile, the general construction sequence is that the bricklayer sticks up from the bottom of a wall tile, always plasters the wall full of tiles, and then paves the floor tiles; The bottom wall of a wall is plastered, but it starts from the penultimate wall tile, and when the floor tile is finished, it is embedded in the bottom wall tile, just above the floor tile.
The difficulty of affixing wall tiles is far greater than sticking them from the ground. There is no support underneath, and it is difficult to ensure complete adhesion until the cement is dry. Therefore, it is inevitable that bricks are dropped. Another difficulty is that the hanging tiles need to be leveled so that the bricks on each wall remain flat.
| Second, what are the advantages of wall tiles? |
1. There is a joint between the wall tiles and the floor tiles in the process of pressing the wall tiles in the floor tiles, that is to say if there is water squatting down on the walls, it will eventually flow down the seam to your waterproof layer. Where is the silting up, and in the long run, certainly not a good thing?
2. What about wall tiles? The water on the wall of the wall flows directly to the glazed surface of the floor tile. Because the floor tile will not be flat, it must form a slope to the floor drain. Therefore, these waters will not stagnate and will eventually flow into the floor drain. Now.
3. Another advantage of tile press tiles is that it is for homes with geothermal conditions.
4. In the process of pressing a brick wall tile, the tile is placed on the wall tile. The brick also has a thermal expansion and contraction coefficient of expansion. Because the ground heat will cause a large change in the ground temperature.
If the heat expands for a long time and there is no room for stretching, it will squeeze the wall tiles for a long time, and finally affect the service life of the wall tiles and floor tiles;
5. In the process of wall tile pressing, the floor tile does not directly reach the wall tile, but rather there is room for expansion of the cement wall behind the wall tile. Therefore, the ceramic tile in the process of ensuring thermal expansion and contraction will not be squeezed.
Tips: According to the order of the wall tiles and floor tiles, we read the article also had a preliminary understanding, in the end how to choose, we still have to determine according to the actual situation, if you do not know how to do, you can consult the construction of experienced master, more More practical decoration knowledge, real shooting with the site, please pay attention to the palm of this site (micro signal: mall_jia).
Tile tile
HPL, called fireproof board, scientific name for the resin impregnated paper high pressure laminated board. HPL( High pressure Laminated) is a surface decorative building materials, refractory has the rich surface color, texture and special physical properties.
HPL is widely used in interior decoration, furniture, kitchen cabinets, closet, exterior wall and other fields.
Kitchen Cabinet HPL,HPL Laminated Sheets,HPL Faced MDF
Luli Group Co.,Ltd. , https://www.cnluli.com