![<?echo $_SERVER['SERVER_NAME'];?>](/template/twentyseventeen/skin/images/header.jpg)
Green fir decoration    Bingyuan Decoration
Misunderstanding 1: The floor is not afraid of blisters is a good floor
In the current market sales, consumers are often faced with asking for a few days to go back and soak for a few days. Whoever buys the floor without swelling will need to spend a long time re-introducing the consumer. Many of these misleadings are those that do not have the expertise to guide consumers.
Well-known basic common sense, wood has the characteristics of rising tide and shrinking, let alone bubble in the water. If you really go to buy a floor that is not deformed in the water for a few days, it will be very bad, because the floor you buy is absolutely the largest, and formaldehyde pollution is also the biggest.
In the national standard, there is a way to measure the water absorption expansion rate, and there are indeed detection methods that are soaked in water. However, the actual operation is such that the test product is soaked in 20 degrees of water for 24 hours and then its moisture absorption expansion rate is measured. There is a certain standard range, too low and too high is not a good floor.
Misunderstanding 2: Use keys or nails to scratch the floor surface
Indeed, this phenomenon is very common now, but there are a lot of misunderstandings here. First of all, the floor wear coefficient is one of the various indicators of the floor, it is important but not all. Judging the advantages and disadvantages of the floor from many aspects, there are environmental indicators, dimensional stability, static bending strength, water swelling, etc., as well as the level of installation, after-sales service and local reputation.
The national standard for measuring the floor wear coefficient is not a key or a nail. In real life, we cannot have a dedicated floor tester to measure the wear resistance. The best way is to sand the floor surface with common sand in the market. After about 50 times of sanding, the surface wear layer did not fall off, and the color of the decorative paper did not become accurate.
And not the better the wear resistance of the floor, the higher the wear resistance will increase the surface of the glial layer, so there are more formaldehyde pollution. In the new national standards, the domestic wear factor has been reduced from a minimum of 6,000 to 4,000 rpm. As long as it exceeds 4,000 rpm, it is sufficient to meet our requirements.
Misunderstanding 3: Solid wood floor surface is burned with lighter
Solid wood flooring has the advantages of environmental protection, naturalness, high-end, comfort, etc. At the same time, it also has the advantages of easy deformation. The surface is not wearable, easy to scratch, and it is afraid of burning. Paint and wood are afraid of burning. If they are burned with fire, I do not know if it is a solid wood floor.
Almost all floors on the market today can be smashed with steel balls, except for PU-painted floors. Determine the pros and cons of solid wood flooring is mainly: wood grade, moisture content is up to standard, processing accuracy, paint adhesion, film hardness, of course, paint abrasion resistance.
Misunderstanding 4: The lower the price, the better
Some consumers feel that the flooring products are similar, so they choose some products with lower prices. Experts believe that any product has a price and quality lever, and if the price is too low, the product quality is poor, and the floor as a high-end, durable consumer goods, its after-sales service in the price share is heavy, can not be sacrificed to reduce prices and services. As far as the market is concerned, products with significantly lower market prices should be carefully discriminated by consumers when making choices.
Five misunderstandings in consumption; no attention to installation
In the flooring industry, there is a saying that "three points of seven-pack floor", the floor is a semi-finished product, must be scientifically installed before the product can be used. Laying technology is directly related to the later use of the floor. Most of the quality problems that occur during the use of wood flooring are due to improper installation. When buying a wooden floor, ask your own carpenter to lay. When the local board finds quality problems, it is easy for both parties to push each other and evade responsibility. And well-known brands of wood flooring companies will provide all-round training for installers, and they can only be qualified after being qualified. When consumers purchase flooring, it is advisable for flooring companies to provide installation standards and understand floor installation procedures.
Misunderstanding 6: Most consumers do not pay attention to floor accessories
The quality of accessories will directly affect the normal use of wood flooring. If the baseboard is not well-matched, it will not only seriously affect the appearance, but will also cause more pollution and affect the normal use of wood flooring.
Baseboards are definitely more of a supporting role than wood floors and are often overlooked by consumers. Many consumers have expressed that when choosing wood flooring, more attention is paid to the wood floor itself, but no more attention is paid to the baseboard, and some consumers even temporarily choose when paving. Baseboard. Because consumers do not pay attention to the quality of wood flooring buried a lot of hidden dangers, in fact, many problems in the wooden floor, its product quality and no problem, the quality problems caused by the skirting and other accessories accounted for about 50% proportion.
Now most of the wood flooring industry's regular brands have implemented kick line charges, and the baseboard has been stripped from the product price. This not only reduces product prices, but also gives consumers more choice. After clarifying the stakes, many sales staff have stated that the owners generally choose the better quality baseboards. From this point, they also greatly improve the quality of wooden floor products.
The price of the baseboard is between a few yuan and a few tens of yuan. In general, the price of a polymer baseboard is about a few yuan, but its quality cannot be compared with other materials. Generally, it can only be used once. The problem can only be changed again. Therefore, this kind of product is not the mainstream product of consumption, but it is the main material for free giving. The quality of solid wood and solid wood finger-joint baseboards is relatively better, and the price is generally between 20 and 60 yuan.
Complimentary accessories are concentrated on small and no-name brands. In fact, they already count the price of the accessories. Since they are free, they try to purchase low-priced accessories to maximize their profits. No one floor supplier will provide free accessories. Better fittings, which also lay a hidden danger for the use of the floor in the future, hurt the interests of consumers.
Flooring purchase home decoration greasy nature floor paint formaldehyde decoration
Mirror is a smooth,highly polished surface covered a thin coating.Mirror is usually a thin coating of metal or dielectrics.
Precision Optical Flats are ideal for a variety of applications including interferometry, imaging systems, laser applications, optical path folding, and auto collimation.
China star optics designs and manufactures a great choice of various high and partially reflecting mirrors for the spectral range:UV,visible,near infrared,and infrared regions.Fused Silica substrates, is optically clear and features excellent resistance to abrasion and high durability, making it the best choice for applications in harsh environments. Metallic coatings Options, Protected Gold, and Protected Silver Coatings available. Wide Variety of Shapes and Sizes available in circular, square, and rectangular dimensions.
Specifications of our Optical mirrors as follow:
*Material:BK7 A glass, Fused silica, Quartz, CaF2,ZnSe,Optical crystals or other glass materials
*Parallelism:1 Arc min
*Clear Apenture:90%
*Squares/Rectangles:1mm to110mm+/-0.2mm
*Center thickness tolerance:+/-0.1mm
*Surface quality:60-40 to 20/10 Scratch/Dig
*Surface flatness:lambda/10 at 632.8nm
Protective Gold Mirror,Au Reflective Coating Mirror,Au Protective Coating Mirror,Protected Gold Mirror
China Star Optics Technology Co.,Ltd. , https://www.opticsrealpoo.com